House: 10 (1 st Floor), Road: 12, Shekhertek, Adabor, Dhaka-1207
Sat - Thu : 10.00 AM - 06.00 PM


AquaArm Ultra Primer

(Formerly known as MYK INDUPRIME EPW 44)

2 Part Water Based Epoxy Resin Primer


AquaArm Ultra Primer is a two-part Epoxy resin based solvent free primer.

Related Product

AquaArm Ultra Coat

(Formerly known as MYK Ultra-Shield)
High thermal Reflectance & Emittance coating


AquaArm Ultra Coat is a single component, water based, high thermal reflectance & emittance coating, it has the ability to reflect the visible, infrared and ultraviolet rays. It significantly lowers the surface temperature of roofs and structural exteriors.

AquaArm TG

(Formerly known as MYK AQUAFIN TG) Multipurpose Waterproof Coating


AquaArm TG is a cementitious, polymer dispersion based flexible protective coating and waterproof barrier. This product is two-component and resistant to water, moisture and abrasion. Its liquid mixing component is solvent free. AquaArm TG is a stand-alone product. It can be top or over coated with flexible or rigid mortars, stuccos or coatings for uniform appearance.

ReArm Rust Remover

(Formerly known as MYK Rust Remover)

Single Component Derusting Solutions


ReArm Rust Remover is very effective product for removing mill scale and rust, besides removing thin films of oil and grease ReArm Rust Remover is formulated using phosphoric Acids and other chemicals. ReArm Rust Remover removes thin films of oil / grease from steel surfaces. Removes mill scale, rust and welding scales. ReArm Rust Remover commands itself to you on many grounds - efficiency, economy, inventory savings in need of water.

Armix Pump AID-P

(Formerly known as MYK PUMP-AID P Concrete Pumping Aid


Armix Pump AID-P is a pumping aid for double piston concrete pumps. Armix Pump AID-P, dissolved in water lubricates the pipe walls and facilitates problem free pumping of cementitious mixes.

Armix Form FR9

(Formerly known as MYK Form FR9)
Oil Based Mould Release Agent


Armix Form FR9 is specially formulated blend of mineral oils and chemicals having release properties which are superior to those of conventional mould oil. The chemicals react with the alkali in the concrete to form a thin water repellent skin on the surface of the mould, thereby enabling easy striping from concrete and acting as a protection to steel and wooden formwork. Armix Form FR9 is supplied as a pale straw colored liquid ready for direct application and use.

Armix Cure WB

(Formerly known as MYK CURE WB - Clear)

Wax Based Curing Compound


The strength and durability of concrete mainly depends upon the concrete curing process/method. All the care taken in the selection of materials like mixing, placing, compaction, etc., will bring to naught if curing is neglected. The curing increases, compressive strength, durability, impermeability and abrasion resistance. Proper curing practice is one of the important steps in making high quality concrete. In addition, the length of curing is also important, the first 3 days is most important in the life of Portland cement concrete. The principle of curing is to prevent the evaporation of the capillary water in the concrete so that sufficient water is available for complete hydration of the cement in concrete. It is basically a white liquid for spraying on freshly cast concrete or newly exposed concrete surface after removal of form work, to form a temporary film which will retain sufficient moisture for effective curing to take place. It is basically low viscosity wax emulsion .This impervious film prevents excessive water evaporation and in turn helps the concrete to more efficient hydration.

FloArm Hard LI +

Liquid Densifier, Sealer, and Dustproofer for Concrete


FloArm Hard LI + is a water-based lithium silicate solution used to densify, seal and dustproof concrete surfaces. FloArm Hard LI + penetrates and chemically reacts within the concrete surface, producing extremely hard and dense calcium silicate hydrate (CSH) in the pores. The result is concrete that is more durable, easier to clean, and more resistant to damage from water and mild chemicals. Because the product of the lithium silicate-concrete reaction is formed internally, the protection of FloArm Hard LI + never peels or flakes off, is unaffected by moisture, and lasts much longer than surface sealers and coatings.

FloArm Hard Q(M)

(Formerly known as MYK TOP 150-M)

Dry shake Monolithic Non-metallic surface Hardener


Ready to use non-metallic floor and surface hardener, based on combination of natural and hard aggregates. The well graded grains/aggregates play an important role in the physical properties of abrasion and wear resistance. It is basically a blend of port land cement and special additives to improve workability, this combination produces a material which is easy to trowel into the fresh surface concrete. FloArm Hard Q(M) provides a dense non-porous surface which is extremely hard wearing and abrasion resistant the standards are quality controlled, factory blended and is ready to use at the site. The floor hardener designed being a non-metallic is antiskid, are rendered tough, wear resistant, dust free, does not rust and do not disintegrate from the floor. It bonds monolithically to the base concrete and it can be applied to

both old and new concrete floors. It can be applied for wet rooms as well as outdoor applications.

ArmGrout HF 66

(Formerly known as MYK Anchor HF 66)

Polyester Resin Anchor Grout


ArmGrout HF 66 is polyester based two component resin system specially made to give excellent anchorage .ArmGrout HF 66 can be used to an anchor size of 25mm Diameter into concrete, rock, masonry or brick work where high speed of installation and early application of load is required.

ArmGrout M-65 E

(Formerly known as MYK Grout M-65 E)

Free Flowing, High Precession, Non-Shrink High Strength Grout


ArmGrout M-65 E is recommended for precision grouting where it is essential to with stand static & dynamic load in typical applications like base plate of Generators, compressors, boilers etc. It is basically a free flow non shrink, high strength expansive grout. It’s formulation is based on port land cement, graded aggregates and additives which impart controlled expansion in the plastic state. The non-shrink grout function is three folds, to fill the voids between the base plate and the concrete foundations completely and permanently without shrinkage or separating from either, to transfer all loads from the base plate to the concrete foundation and to maintain precise alignment. It effectively transfers all operational loads to the foundation.

ArmGrout Additive

(Formerly known as MYK GROUT ADD)

Expansive Grout Additive


ArmGrout Additive is a specially formulated grouting aid. It plasticize the mix allowing for substantial reduction in water content without affecting the fluidity, thus improving the strength and impermeability of the grout. During the setting period of the grout it produces controlled expansion to compensate the normal plastic shrinkage of cement.


A single pack powder grout additive which when added to cement produces a free flow non-shrink grout.

ReArm Fix 10S

(Formerly known as MYK FIX 10-S)

Fast Settling Cement


It is chloride free quick setting cement after addition of water its sets instantly and useful for plugging purpose.

SealArm PS -P

(Formerly known as MYK SEAL PS P)

Two Part Polysulphide Sealant, Pouring Grade


SealArm PS–P is a two pack Polysulphide based, tough flexible durable with strong adhesive sealant and is a pourable version, basically used for movement joints in concrete and pavements

ReArm Crete MC(G)

(Formerly known as MYK CRETE MC(G))

Economical, General purpose, non-shrink, cementitious micro concrete Grout


ReArm Crete MC(G) is a ready to use single component dry powder Cementitious material. It is supplied as a pre blended polymer modified dry powder, which post addition of recommended water at the site produces a non-shrink, free-flowing and high strength micro concrete. This is specially designed for repair to damaged reinforced concrete. It is suitable for use in wide range of repairs, pavements, ramps etc.

ReArm Crete RM-HS

(Formerly known as MYK CRETE RN HS)

Polymer modified one component re mortar for hand and machine application


ReArm CRETE RM HS is a pre-batched one component polymer modified repair mortar.

ReArm Bond EBA

(Formerly known as MYK Bond EBA)
Epoxy Resin Based Concrete Bonding agent


ReArm Bond EBA is a solvent free epoxy resin, which is supplied as a two-pack component in pre- weighed quantities for ready to mix and use condition.

Standards compliance: ASTM C881: Type II, Grade 2 Class C

ReArm SBR 45

(Formerly known as MYK Bond SBR 45)

Cement Mortar and screed modifier cum bonding agent


ReArm SBR 45 is a modified Styrene butadiene Rubber emulsion specially designed for use as a mortar modifier for cementitious systems and a bonding aid. It is suitable as an admixture for obtaining waterproof concrete, plasters and

mortars. It is also suitable for preparation of repair mortars damaged and spalled concrete.

Armix Emme Crete SP 111 R

(Formerly known as MYK SAVEMIX SP 111 R)
High Performance, Super Plasticizing Admixture


Armix EmmeCrete SP 111 R is supplied as a brown liquid instantly dispersible in water Armix EmmeCrete SP 111 R has been specially formulated to give high water reductions up to 20% without loss of workability or to produce high quality concrete of reduced permeability.

Armix CI- Bipolar

(Formerly known as MYK Savemix CI- Bipolar)

Bipolar Concrete Penetrating Corrosion Inhibiting Admixture


Armix CI- Bipolar is a bipolar corrosion inhibiting liquid concrete admixture for use in reinforced concrete and mortar. It acts as a corrosion inhibitor for the steel reinforcement. By using Armix CI- Bipolar, the life expectancy and durability will be substantially.

Armix HyyeCrete PC20(MC)

High Performance concrete superplasticiser, based on polycarboxylic technology


Armix HyyeCrete PC20(MC) differentiated from conventional super plasticizers in that it is based on a unique carboxylic ether polymer with long lateral chains. This greatly improves cement dispersion. At the start of the mixing process an electrostatic dispersion occurs but the cement particle’s capacity to separate and disperse. Thismechanism considerably reduces the water demand in flowable concrete.

Armix HyyeCrete PC20(MC) combines properties of water reduction and workability retention. It allows the production of high performance concrete and/or concrete with high workability.

Armix HyyeCrete PC20(MC) is a particularly strong super-plasticizer allowing production of consistent concrete properties around the required dosage.


(Formerly known as MYK Proof WP10)

Chloride Free Integral Liquid Waterpro Admixture for Concrete and Mortar


AquaArm Proof IWP-10 is a chloride free liquid based on selected sugar reduced Ligno Sulphonates.
AquaArm Proof IWP-10 waterproofs by improving the quality of the Concrete or Mortar. It reduces the water demand for required workability and minimizes segregation and bleeding. It is in liquid form and shows excellent dispersion and is more efficient compared to traditional powder water proofers.


(Formerly known as MYK REMICRETE PC 10)

High Performance concrete superplasticiser, based on polycarboxylic technology


Armix Emmecrete PC 10 is a unique combination of the latest generation superplasticisers , based on a polycarboxylic ether polymer with long lateral chains. This greatly improves cement dispersion.
Armix Emmecrete PC 10 combines properties of water reduction and workability retention. It allows the production of high performance concrete and/or concrete with high workability.

Armix Emmecrete PC 10 is a particularly strong super-plasticiser allowing production of consistent concrete properties around the required dosage.